The LiteBIRD satellite will map the polarisation of the Cosmic Microwave Background (CMB) with unprecedented sensitivity by means of antenna-coupled transition edge sensors (TESs). Its current design features single SQUID-Array Amplifiers (SAA) at a temperature of about 400 mK in order to read out up to 64 TESs in a frequency division multiplexing scheme. The front-end part of the electronics (the SQUID Controller Assembly -SCA) was designed to handle this configuration. Nevertheless, alternative configurations of the experiment are being studied that might require a dual-stage SQUID (DSS) amplification chain in order to meet thermal and noise requirements. In light of this possibility, we have successfully investigated the feasibility of controlling two individual SAAs in a DSS Amplifier (DSSA) configuration with two independent channels of the present SCA. The SQUID directly connected to the sensor, commonly referred to as ‘front-end’, behaves as an emitter-follower, or buffer, circuit and it decouples the impedance of the TES(s) from the rest of the readout chain whilst producing a moderate amplification. The second SQUID, ‘booster’, is responsible for a high-gain amplification of the signal and can be thermally decoupled from the front-end allowing it to dissipate a lot more power and thus exhibiting a higher gain. We characterised a breadboard model in which two SQUID amplifiers are cascaded but hosted on the same circuit board and thus not thermally decoupled. This was intended to perform functional tests and to assess the feasibility of controlling a DSSA without introducing major changes in the already developed LiteBIRD SCA. We present the typical I-V and I-Φ curves of the two SQUIDs along with the characterisation of the DSSA in terms of bandwidth, linearity and total harmonic distortion (THD).
De Lucia, M., Dalbo, P., Tartari, A., Cliche, J., Conenna, G., Coppi, G., et al. (2026). Compatibility Study of the LiteBIRD SQUID Controller Unit With a Dual-Stage SQUID Amplification Chain. IEEE TRANSACTIONS ON APPLIED SUPERCONDUCTIVITY, 1-6 [10.1109/TASC.2026.3690793].
Compatibility Study of the LiteBIRD SQUID Controller Unit With a Dual-Stage SQUID Amplification Chain
Coppi G.;Zannoni M.;
2026
Abstract
The LiteBIRD satellite will map the polarisation of the Cosmic Microwave Background (CMB) with unprecedented sensitivity by means of antenna-coupled transition edge sensors (TESs). Its current design features single SQUID-Array Amplifiers (SAA) at a temperature of about 400 mK in order to read out up to 64 TESs in a frequency division multiplexing scheme. The front-end part of the electronics (the SQUID Controller Assembly -SCA) was designed to handle this configuration. Nevertheless, alternative configurations of the experiment are being studied that might require a dual-stage SQUID (DSS) amplification chain in order to meet thermal and noise requirements. In light of this possibility, we have successfully investigated the feasibility of controlling two individual SAAs in a DSS Amplifier (DSSA) configuration with two independent channels of the present SCA. The SQUID directly connected to the sensor, commonly referred to as ‘front-end’, behaves as an emitter-follower, or buffer, circuit and it decouples the impedance of the TES(s) from the rest of the readout chain whilst producing a moderate amplification. The second SQUID, ‘booster’, is responsible for a high-gain amplification of the signal and can be thermally decoupled from the front-end allowing it to dissipate a lot more power and thus exhibiting a higher gain. We characterised a breadboard model in which two SQUID amplifiers are cascaded but hosted on the same circuit board and thus not thermally decoupled. This was intended to perform functional tests and to assess the feasibility of controlling a DSSA without introducing major changes in the already developed LiteBIRD SCA. We present the typical I-V and I-Φ curves of the two SQUIDs along with the characterisation of the DSSA in terms of bandwidth, linearity and total harmonic distortion (THD).
I documenti in IRIS sono protetti da copyright e tutti i diritti sono riservati, salvo diversa indicazione.
